Save more with MULTIPACKS!
Rapid Application Moss Mould Remover
Regular price
Sale price
$99.95
Rapid Application® Moss and Mould Remover and the original blue Wet and Forget® Moss and Mould Remover, have exactly the same active ingredient and will cover a similar area. It is only the actual application (using the revolutionary Reach Nozzle® that is so different.
IMPORTANT: You cannot use regular blue Wet & Forget with the new Rapid Application product. It will NOT work as the dilution rates are very different!
-
Rapid Application® is non caustic and non acidic and contains NO bleach.
-
Rapid Application® is your concentrate and garden sprayer all in one.
- The most outstanding feature of Rapid Application® is its Reach Nozzle™ with its unparalleled reach of 8m or 2 storeys without using a ladder! How amazing is that? You don't need a ladder!
- For large concrete driveways, paths etc - a quick change on the revolutionary Reach Nozzle™ gives you an incredibly fast application - more than fifty times that of a garden sprayer.
If I am on tank water, can I use Rapid Application on my roof?
Sure can. But you must disconnect the water supply to your tank for 3-4 weeks or have at least 36ml of rain to remove the concentrate. Wet and Forget has been used for over 35 years to treat biological growth on roofs.
Do I have to use Rapid Application all at once?
No, but good planning is essential. Work to a pattern so you know where you have started and stopped. The product is fine if left in the spray container as it does not deteriorate when it has been diluted.
How long will Rapid Application last in the container?
Rapid Application has unlimited shelf life. Always the container out of reach of children.
How long does it take Rapid Application to work?
It is totally dependent on the intensity of the contamination. If it is really light you will see results within days. Otherwise it may take approximately 2-3 months to see improvements. Your concrete may turn an orangy brown when the Rapid Application is applied. This is normal and shows you have had a good reaction. The discoloration will dissipate over a short period of time and is not permanent. The good news is that when you use it again the following season, the clean up will occur within weeks. In the very worst case scenario where contamination is extreme, it may take 6-12months.
What is the coverage area of Rapid Application?
Every 2L pack covers between 150-300 sq m depending on the porosity of the surface and the level of contamination. ie painted surfaces will use less product but porous surfaces readily absorb the product and therefore coverage could be in the range of 100-150sq m.
When is the best time to apply Rapid Application?
On a cool, dry windless day and when no rain is expected for 4-6 hours. Often the evening is best when evaporation of the product is minimal. This will ensure that the surface to be treated stays wet with Rapid Application for an extended period.
Will Rapid Application affect my pets?
Not under normal circumstances. However, keep your precious animals off the treated surface until it is dry, to ensure they don't ingest any of the product. If they accidentally walk or sit in the product - wash their feet and bottoms with fresh water as a precaution.
Will Rapid Application damage my plants?
Not unless you are directly spraying it onto the plants. If you accidentally do this, then rinse the plants down with water from the hose. Or better still, protect them with paper or plastic to avoid overspray.
Will Rapid Application remove the mould off my timber decks?
Most definitely! But if your deck is older and has never been cleaned, it may be noticeably blackened with the contamination. In this case, it would be advantageous to wait a month after the application of Rapid Application and give the area a light brush with a broom or scrubbing brush with warm water to remove it. The good news is that you should only have to do this once and then the maintenance becomes so easy. Also check out our other product, Hit The Deck, for a more instant result (although it does involve more elbow grease!)
Will Rapid Application get moss out of lawns?
You will need to use Wet and Forget as the dilution rates are different. Firstly lightly water the lawn but not enough to saturate the moss. Do this late in the day when the sun is low so that evaporation is kept to a minimum. Dilute the 5L Wet & Forget 7 parts water to 1 part Wet & Forget and spot spray the moss. You may have to give it a couple of goes until you have it under control. At worst you may get slight burning on the grass but it will recover very quickly. Rake the dead moss out. then sprinke lime over the area as this is usually a sign that your pH of the soil is not quite right.
How much Rapid Application will I need to clean my roof?
The average 3 bedroom tile roof is approx 150sq metres but because of the undulations of the tile profile the actual area is a lot bigger. Therefore an average tile/concrete roof would require 2 x 2L packs, depending on how porous the surface is and how much biological growth is present. For an average 3 bedroom tile roof with lichen you would require 3 x 2L packs depending on the total area covered with lichen. For best results, spot spray the lichen, leave for 10-15 minutes and then respray the lichen and the entire roof to ensure the plant absorbs the Rapid Application thoroughly. the first application is to dissolve the waxy surface. The 2nd spray will then penetrate the lichen. For green moss and black mould, one application is normally sufficient. Your roof will normally take between 6 & 12 months to come clean.
+ Rapid Application® is safe to use on any exterior surface.
+ Rapid Application® uses our revolutionary Reach Nozzle™ to reach 8m (2 storeys)
+ Rapid Application® is an extremely fast way to apply the product with its Reach Nozzle™
+ Rapid Application® means that you don’t need to use ladders! So much safer!
+ Rapid Application® has an unlimited shelf life.
+ Rapid Application® cleans without having to waterblast or scrub the surface.
+ Rapid Application® is non acidic, non caustic & contains no bleach.
+ Rapid Application® requires no mixing & no measuring. So there’s no mess!
Use safely on Absolutely ANY exterior surface!
Roofs
Decramastic, Clay tile, Concrete tile, Super 6, Fibrolite, Colour steel, Zincalume (iron roof)
|
|
Removing Lichen from any Exterior Surface
- Visually, section your area off into manageable parts.
- Spot spray the lichen within each section.
- Leave for 15-20 mins (while it is still damp) and then respray the lichen and the entire area of that particular section to ensure the plant absorbs the Wet & Forget/Rapid Application thoroughly.
- The first application is to dissolve the waxy surface.
The 2nd spray will then penetrate into the roots. - This will ensure much better results for you. Remember that it will still take time to decompose and break away.
- Connect Rapid Application® Reach Nozzle™ to your hose.
- There is nothing like this on the planet!
- This revolutionary and fast Reach Nozzle™ reaches 8m (2 storeys high).
- There’s no mess and no mixing!
Turn dial to “Water” and turn tap on until you are happy with the pressure. - Rotate black dial on the Reach Nozzle™ to the ‘ON’ setting
- Begin spraying in a logical pattern to ensure a thorough coverage of the surface.
- Your job is done.
Watch the surface come clean bit by bit, with the help of Mother Nature. - There 2 settings below are for spray adjustment
